Precision Pulse and Calibration Technology

Development of precise high-voltage and high-current pulse technology for the calibration and characterization of electrical measurement systems.

Four oscilloscope probes around a measured waveform: passive probe, differential probe, current clamp and Rogowski coil

High voltage, high currents and fast switching – precise and reproducible.

Developing high-performance calibration generators places high demands on circuit design, PCB layout and metrological verification. The combination of high voltages or currents, steep signal edges and high accuracy is particularly challenging.

Our development experience covers the generation of defined voltage and current pulses for the calibration and characterization of electrical measurement systems.

Precise High-Voltage Pulses

For the calibration of high-voltage probes and voltage measurement inputs, square-wave voltage pulses with amplitudes of up to 6 kV are generated. Slew rates of more than 100 V/ns make it possible to investigate the dynamic transfer behaviour of fast measurement systems.

Probe compensation

Voltage pulse

In addition to the pulse shape, the accuracy of the output voltage is decisive. A DC voltage accuracy of 0.1 % places high demands on voltage references, control and measurement technology.

The technical challenge lies above all in mastering parasitic inductances and capacitances, insulating high voltages and reproducibly generating fast signal edges.

The schematic shows the basic principle: a high-voltage source charges two buffer capacitors. A changeover switch connects either the positive or the negative pole to ground and thus determines the polarity of the pulse. Two fast switches in a half-bridge arrangement switch the output between the two potentials and generate the steep edges at the BNC output.

Schematic of the high-voltage pulse generator

Technical data:

  • Voltage pulses up to 6 kV
  • Positive and negative output voltage
  • Slew rate > 100 V/ns
  • DC voltage accuracy 0.1 %
  • Programmable pulse width and repetition rate
  • PC interface for remote operation (e.g. USB, GPIB, …)
  • Application: calibration of high-voltage probes and voltage measurement inputs

Dynamic High-Current Calibration

For the dynamic calibration of current sensors, square-wave current pulses of up to 1000 A with current slew rates of up to 1 A/ns are generated.

Such pulses serve as defined reference signals for testing current clamps, Rogowski coils and other current sensors. In particular, they allow the transient response and signal transmission during fast current changes to be characterized.

Generating such current pulses requires low-inductance current paths, suitable power switches and a careful design of the entire pulse circuit.

Technical data:

  • Square-wave current pulses up to 1000 A
  • Typical current slew rate 1 A/ns
  • Application: calibration of current clamps, Rogowski coils and current sensors

Key Technologies

Fast Switching Circuits

Generation of defined pulses with high voltage and current slew rates. The dynamic behaviour of the power switches and the minimization of parasitic circuit elements are decisive.

Analog Precision Electronics

Development of precise reference, measurement and control circuits. The combination of high static accuracy and fast dynamic processes places special demands on circuit design.

Low-Inductance and EMC-Compliant Design

With fast switching transients, even small parasitic inductances and capacitances have a considerable influence on signal quality. An optimized PCB layout and careful design of the current paths are therefore essential parts of the development.

Microcontrollers and Embedded Software

Microcontroller-based control systems handle the configuration, monitoring and sequence control of the calibration generators. Development covers both the low-level embedded software and the integration of the controller into the overall system.

Digital communication interfaces allow the devices to be controlled remotely and integrated into automated measurement and test systems.

Precision Measurement

Characterizing fast high-voltage and high-current pulses requires suitable measurement methods and a thorough understanding of how the measurement setup, sensors and signal transmission affect the result.

Expertise for Demanding Electronics Development

Developing precise pulse sources brings together different disciplines of electronics: from analog precision circuits and power electronics through microcontroller technology and embedded software to fast measurement technology.

In addition to the development of the electronic hardware, our technological expertise also includes the digital control, the implementation of communication interfaces and the integration into automated test systems.

This interdisciplinary experience forms the basis for developing custom measurement, test and power electronics – from circuit design to the fully functional overall system.